iphone

Bienvenue sur Mon Site Personnel

Ndeye Awa SENE



........

NDEYE AWA SENE, Profeseur Assimilé

Enseignante chercheure

Université Cheikh Anta DIOP

Ecole Supérieure Polytechnique
Département Génie Civil
Email: ndeyeawa.sene@esp.sn, awa.sene@ucad.edu.sn
Mes Publications
2024
[1] Gaye A., Sène N. A., Balland P., Sambou V., Gning P. B.
"Physical and Morphological Charactérisation of Typha Australis Fibres "
Material Sience Forum, ISSN 1662-9752, Vol.1122, 99-110


2023
[2] Bousso N. C., Touré A. O., Sène N. A., Fall N. M., Keinde D., Sambe F. M., Sambou V.,
"Fabrication d’un liant hydraulique alcaline des cendres volantes avec incorporation de Phosphogypse "
Afrique Science, ISSN 1813-548X, 23(3), 78-90,


[3] Thiam G., Sène N. A., Balland P., Thiam A. A.,“
"Mechanicals properties of mortars based on glass waste as a partial replacement for cement"
International Journal of Advanced Research, DOI:10.21474/IJAR01/178537, 11(11), 517-523


[4] Thiam G., Sène N. A., Balland P., Touré A. O.,
"Physical and Thermal Characterization of Glass Powder and Coffee Grounds for the Production of Building Materials "
Journal of Scientific and Engineering Research, 10(9):30-34


[5] Ba A. M., Bodian S., Sène N. A., Touré A. O., Niang I., Gaye A., Thiam, G. Dieng E., Faye M. and Sambou V
"Physical characterization of excavated soils in diamniadio-senegal"
International Journal of Advanced Research. DOI:10.21474/IJAR01/1744611(08), 745-750


[6] Nikiéma D., Sène N. A., Balland P., Sergent A.,
"Study of walls’ influence on the mechanical properties of 3D printed onyx parts: Experimental, analytical and numerical investigations"
Heliyon 9 e19187


[7] Gaye A., Sène N. A., Balland P., Sambou V., Gning P. B., Magnien A.,
"Elaboration and Mechanical Characterisation of Composites Reinforced with Typha Australis Fibre "
Journal of Scientific and Engineering Research, 10(9):65-69


[8] Gaye A., Sène N. A., Balland P., Sambou V., Gning P. B.,
"Extraction and physicomechanical characterisation of Typha Australis fibres: Sensitivity to a location in the plant"
Journal of Natural Fibers, 20:1, 2164106, DOI: 10.1080/15440478.2022.2164106 To link to this article: https://doi.


2022
[9] Thiam G., Sène N. A., Balland P., Toure A. O
"Physical characterization of glass powder and coffee grounds for the elaboration construction materials"
VIIème Edition CasamanSun-FITER, Sénégal


[10] Ba A. M., Bodian S., Sène N. A., Touré A. O., Niang I., Gaye A., Thiam G., Dieng E., Faye M., Sambou V.
"Physical characterization of excavated soils in diamniadio-senegal"
11th International Conference of the African Materials Research Society, AMRS2022,


[11] Thiam G., Sène N. A., Balland P., Toure A. O.
"Physical and thermal characterization of glass powder and coffee grounds for the elaboration construction materials"
11th International Conference of the African Materials Research Society, AMRS2022


[12] Gaye A., Sène N. A., Balland P., Sambou, V., Gning P. B., Magnien A
"Elaboration and mechanical characterisation of composites reinforced with Typha Australis fibre"
11th International Conference of the African Materials Research Society, AMRS2022


[13] Gaye A., Sène N. A., Balland P., Sambou, V., Gning P. B.
"Physical and morphological characterization of typha australis fibres"
2ème conférence sur les éco-matériaux en Afrique, CEMA 2022, Sénégal,


2021
[14] Gaye A., Sène N. A., Balland P., Sambou, V., Gning P. B.
"Caractérisation mécanique des fibres de typha australis"
Congrès des jeunes chercheurs en mécanique, Méca-J 2021, en ligne,


[15] Bodian Séckou, Faye Mactar, Sambou Vincent, Sene N. Awa, Diaw Ibrahima, Faye Kory
"Caractérisation physico-chimique des matières premières argileuses de la carrière de thicky (sénégal) pour la fabrication de briques en terre"
Journal de Physique de la SOAPHYS, Vol 3, N°1 C21A01. http://dx.doi.org/10.46411/jpsoaphys.2021.01.01.


[16] Bodian S., Faye M., Sène N. A., Sambou V., Dieye Y.,
"Physico-chemical characterization of clay raw materials from theThicky quarry (Senegal) for the manufacture of earth bricks"
J Sustain Const Mater Technol, Vol. 6, Issue. 3, pp. 87–94


2019
[17] Phung H. A., Balland P., Sène N. A., Tabourot L.
"Experimental design on bimaterial forming "
24ème Congrès Français de Mécanique, (Brest, France)


[18] Phung H. A., Balland P., Sène N. A., Tabourot L.
"About localization on plane strain tensile test on bimaterial specimen"
AIP Conference Proceedings, 2113, 180004 (2019)


2018
[19] Sène N. A., Balland P., Arrieux R., Bouabdallah K.
"Experimental study of Portevin - Le Châtelier bands on tension and equi-biaxial tension"
Archives of civil and mechanical engineering, http://dx.doi.org/10.1016/j.acme.2017.05.005, Volume 18, issue 1, pp. 94-102


[20] Bodian S., Faye M., Sène N. A., Sambou V., Limam O., Thiam A.
"Thermo-mechanical behavior of unfired bricks and fired bricks made from a mixture of clay soil and laterite"
Journal of Building Engineering 18 172–179


[21] Tabourot L., Charleux L., Balland P., Sène N. A., Balland P., Andreasson E.
"Experimental characterization and microstructure linked modeling of mechanical behavior of ultra-thin aluminum foils used in packaging"
AIP Conference Proceedings, p. 170016-1 – 170016-6


[22] Gaye A., Guèye P. M., Keinde D., Sène N. A.
"Thermo-mechanical study of artificial aggregates-based concrete derived from the Thicky clays (Senegal)"
International Journal of Innovation and Applied Studies, ISSN 2028-9324 Vol. 24 No., pp. 1614-1628


2017
[23] N. S. Fall, D. Keinde, N. A. Sène, S. Ndoye, P. M. Guèye
"Effet de la nature de l’eau en provenance du Sénégal sur l’essai de compression du béton"
Journées nationales du béton, JNB’17 (Hammamet, Tunisie)


[24] N. A. Sène, P. Balland, R. Arrieux
"Etude de l’influence de la direction de laminage sur les courbes limites de micro-formage"
23ème Congrès Français de Mécanique, (Lille, France)


[25] Fall N. S., Keinde D., Sène N. A., Ndoye S., Guèye P. M.
"Etude de l’influence des caractéristiques physico-chimiques de l’eau provenant du Sénégal sur les propriétés mécaniques du béton : cas de Tivaouane Peulh, Thiaroye, Rufisque, Thiès et Léona"
Afrique Science, ISSN 1813-548X, Volume 13, Issue 1, p.277-286


[26] Sène N. A., Keinde D., Ba S. G., Guèye P. M.
"Etude du comportement mécanique d’un béton renforcé aux fibres métalliques"
Afrique Science, ISSN 1813-548X, Volume 13, Issue 4, p. 286-297


[27] Keinde D., Sène N. A., Dione M., Guèye P. M.
"Study on sand concrete from Senegal"
Science Appliquée et de l’Ingénieur, ISSN 2312 – 8712, Volume 2.1, p. 29-36


[28] Tabourot L., Sène N. A., Balland P., Ksiksi N., Charleux L., Issack M.“
"Comparative Study of Modelling Efficiency Regarding Localization Development"
AIP Conference Proceedings, 1896 ; doi: 10.1063/1.5008182, p. 160007-1 – 160007-6


2016
[29] Sène N. A., Balland P., Tabourot L., Vautrot M., Ksiksi K., Arrieux R
"An original prediction of localisation during tensile and biaxial expansion tests on copper by the compartmentalized model"
AIP Conference Proceedings’ 1769, 160010, doi: 10.1063/1.4963553, p. 16010-1 – 16010-6,


2015
[30] L. Tabourot, P. Balland , N. A. Sène, N. Ksiksi
"Détection de l'apparition de la localisation dans la simulation d'opérations de formage des tôles métalliques"
22ème Congrès Français de Mécanique (Lyon, France)


[31] Tabourot L., Balland P., Bizet L., Sène N. A., Déprès C., Balan T., Manach P. Y.
"Young’s modulus determination: influence of microplasticity a pseudo-elasticity on metal forming"
Key Engineering Materials, DOI 10.4028/www.scientific.net/KEM.651-653.598, Volume 651-653, p 598-603


2014
[32] Tabourot L., Balland P., Sène N. A., Vautrot M., Ksiksi N., Maati A.
"Numerical study of the impact of constitutive modelling on the evolution of necking in the case of a tensile test on C68 grade steel"
Key Engineering Materials, DOI 10.4028/www.scientific.net/KEM.611-612.521, Vol. 611-612, p. 521-528


2012
[33] Sène N. A., Balland P., Arrieux R., Bouabdallah K.
"An experimental study of the micro-formability of very thin materials"
Experimental Mechanics, DOI 10.1007/s11340-012-9623-3, Volume 53, Issue 2, p. 155 – 162


[34] Sène N. A., Balland P., Arrieux R.
"Numerical determination of micro-forming limit diagrams: introduction of the grain size heterogeneity"
Modelling and Simulation in Materials Science and Engineering, DOI 10.1088/0965-0393/20/4/045020, Volume 20, Issue 4, p. 1-12


2011
[35] Sène N. A., Balland P., Arrieux R.
"Introduction d’hétérogénéités de microstructure pour la prédiction numérique de l’apparition de la striction sur matériaux très minces"
20ème Congrès Français de Mécanique (Besançon, France)


[36] Sène N. A., Balland P., Arrieux R.
"Numerical study of the micro-formability of thin metallic materials: virtual micro-forming limit diagrams"
Archives of Civil and Mechanical Engineering, DOI 10.1007/s12289-011-1068-1, Volume 11, Issue 2, p. 421 – 435


[37] Dumoulin S., Hopperstad O. S., Sène N. A., Balland P., Arrieux R., Moreau J. M.
"Numerical modelling of plastic forming of aluminium single crystals"
International Journal of Material Forming, DOI 10.1007/s12289-011-1059-2, Volume 6, Issue 1, p. 41-48


[38] Sène N. A., Balland P., Arrieux R.
"Determination and validation of micro-forming limit diagram of very thin materials"
International Journal of Material Forming Volume 11, Issue 10, p 422-434


2010
[39] Sène N. A., Balland P., Arrieux R., Sangharé M.
"Détermination des courbes limites de micro-formage virtuelles : introduction d’hétérogénéités géométriques et de microstructure"
Journées scientifiques et techniques en mécanique des matériaux (Tunisie)


[40] Sène N. A., Balland P., Arrieux R., Moreau J. M
"Micro-deep drawing on aluminium crystals in order to validate multiscale modelling"
Experimental Mechanics, DOI: 10.1007/s11340-010-9398-3, p. 1007 – 1016,


2008
[41] Sène N. A., Balland P., Arrieux R.
"About necking detection to determine forming limit diagrams for mini stamping"
17th International Scientific and Technical Conference “Design and Technology of Drawpieces and Die Stampings” (Pologne)